Experimental Investigations of Pull-Out Behaviour of Synthetic Fibres

S t r e s z c z e n i e Wytrzymałość oznaczona metodą „pull-out” należy do podstawowych cech betonu zbrojonego włóknami. W literaturze rzadko prezentuje się modele analityczne opisujące zachowanie włókien syntetycznych w badaniu „pull-out”. Co więcej, istniejące modele nie są poparte kompleksowymi badaniami doświadczalnymi. W tym artykule przedstawiono wyniki takich badań. Na wstępie porównano ze sobą wyniki jednoi dwustronnych badań „pull-out”. Następnie zbadano wpływ wytrzymałości zaprawy, powierzchni włókien i długości zakotwienia włókien dla próbek jednostronnie kotwionych. Żaden z dostępnych modeli analitycznych dla włókien syntetycznych nie był ściśle zgodny z wynikami badań doświadczalnych. Stąd, zaproponowano modyfikację prawa tarcia (relacja τ-s) w modelu dla włókien stalowych, w celu uzyskania najbardziej precyzyjnego przybliżenia dla metody „pull-out” dla włókien syntetycznych. Dla odpowiednio dobranego modelu określono krytyczną długość zakotwienia. K e y w o r d s : Critical anchoraged length; Experimental investigation; Mechanical model; Pull-out behaviour; Synthetic fibres. 2/2018 A R C H I T E C T U R E C I V I L E N G I N E E R I N G E N V I R O N M E N T 89 A R C H I T E C T U R E C I V I L E N G I N E E R I N G E N V I R O N M E N T The Si les ian Univers i ty o f Technology No. 2/2018 d o i : 1 0 . 2 1 3 0 7 / A C E E 2 0 1 8 0 2 6 M . E . T ó t h , A . P l u z s i k , T . P l u z s i k , B . M o r l i n beam results can be compared to each other by a fictive pull-out force eliminating the high deviation caused by the different amounts and distribution of fibres in the critical cross-section. The pull-out behaviour is one of the distinctive features of fibre reinforced concrete. The more we know the phenomenon of the pulling out the better we understand the mechanical behaviour of the FRC material. It can usually be observed that fibres are mainly pulled out rather than torn in the cracked cross-section of a FRC beam [7]. The higher ductility of FRC compared to plain concrete and the residual tensional strength after the first crack is due to the frictional stresses acting on the interface of the fibres and the concrete during the slipping of the fibres in the cracked zone. In the new beam model according to Tóth, Pluzsik and Juhász [7] the fictive pull-out force was assumed to be constant. The aim of this work is to choose a more appropriate analytical model for the pull-out of synthetic fibres which can be built in the beam model to improve it and to gain a more precise approximation of the experimental load-displacement curves for FRC beams. Few analytical models for the pull-out of synthetic fibres can be found in the literature [8 and 9]. The existing models are not supported by comprehensive experimental investigations. A more detailed analysis can be found for steel fibres [10], however, the question arises whether the existing models can be applied for synthetic fibres. 2. TESTING METHOD, EXPERIMENTAL RESULTS Although the pull-out of fibres in a FRC beam is determined mainly by the bonding of the fibre surface and the mortar in the concrete, it is affected by a lot of other factors (aggregate type, porosity, efficiency of the compaction, chemical admixtures...). Thus, there is no simple, determinable relation between the concrete strength and the maximum pull-out force. To eliminate the uncertainties mentioned above, mortar samples were used in the experiments. The samples were prepared based on the requirements of EN 196-1 standards in the Miskolc Cement Laboratory of CRH. Two series of the samples were prepared with five different cement contents in both. The standard cement content was changed in the samples by refilling the missing cement part with limestone powder (Table 1). The water-mix ratio (mix means cement and limestone) was held on 0.5 (standard value) in all samples while the water-cement ratio changed proportionally with the reduction of the cement content. In the first series five two-side anchoraged and five one-side anchoraged samples were made for each different cement content and for both fibre types, respectively. In the second series one-sided samples were made with three different anchoraged lengths, five different cement contents and two fibre types, respectively. Five pieces of samples were made for every similar case (similar anchoraged length, cement content and fibre type). 90 A R C H I T E C T U R E C I V I L E N G I N E E R I N G E N V I R O N M E N T 2/2018 Table 1. Experimental samples Experimental samples five pieces of every similar case All of the mix prepared from 1250 g standard sand (according to EN 196-1), sum total 450 g CEM I 42.5 R cement and limestone powder and 225 g water, water-mix (cement and limestone) ratio 0.5 Sign of the sample Cement content of the mix [g] Limestone powder content of the mix [g] Fibre type Anchoraged length [mm] Anchoragement type 150_20 150 300 waved/ribbed 20 one-sided/ two-sided 225_20 225 225 waved/ribbed 20 one-sided/ two-sided 300_20 300 150 waved/ribbed 20 one-sided/ two-sided 375_20 375 75 waved/ribbed 20 one-sided/ two-sided 450_20 450 waved/ribbed 20 one-sided/ two-sided 150_15/ 150_20/150_25 150 300 waved/ribbed 15/20/25 one-sided 225_15/ 225_20/225_25 225 225 waved/ribbed 15/20/25 one-sided 300_15/ 300_20/300_25 300 150 waved/ribbed 15/20/25 one-sided 375_15/ 375_20/375_25 375 75 waved/ribbed 15/20/25 one-sided 450_15/ 450_20/450_25 450 waved/ribbed 15/20/25 one-sided E X P E R IM EN TA L I N V E S T I G AT I O N S O F P U L L O U T B E H AV I O U R O F S Y N T H E T I C F I B R E S The experiments took place in the polymer laboratory of TUB according to the measure method used in case of fibre reinforced plastic. The speed of the pullout was 10 mm/min. The pull-out tester was the ZWICK/ROELL Z005 universal material testing machine. Because of the restriction of the length of this paper not all the experimental results are presented here, only representative samples are shown. The curves in the following figures are calculated as an average of 3–5 similar samples. Two fibre types which had different surface characteristics (ribbed, waved) were examined (Fig. 1). In Fig. 1 the pull-out curves of the two types of fibres are compared in case of one-sided samples, with 300 g cement content and 20 mm anchoraged length. Although the ribbed fibres had higher maximal force in all cases, after the maximum force the waved fibres behaved more favourably in the descending part of the pull-out function. The speciality of ribbed fibres furthermore was the systematic jumps in the descending part of the curves as a result of the surface shaping. Aside from the above differences the curves for both fibre-types had similar main features in all examined cases. Ultimately, these fibre-types can be modelled by the same theoretical model. C I V I L E N G I N E E R I N G 2 /2018 A R C H I T E C T U R E C I V I L E N G I N E E R I N G E N V I R O N M E N T 91 Figure 2. Oneand two-sided samples in pull-out tester Figure 1. Ribbed and waved fibres and experimental F-u curves for one-sided case, cement content: 300 g, anchoraged length: 20 mm Figure 3. Oneand two-sided pull-out with 300 g cement content and 20 mm anchoraged length ce M . E . T ó t h , A . P l u z s i k , T . P l u z s i k , B . M o r l i n A one-side anchoraged sample can more easily be carried out in the laboratory, however, according to the literature [9] the phenomenon of the two-sided pull-out, which really occurs in the cracked cross-section of an FRC beam, has significantly different features. In the present experiment fifty two-sided and fifty one-sided samples were made with various cement contents as well (Table 1, Fig. 2) to examine the differences between the one-sided and two-sided phenomena. In Fig. 3 as a typical example the one-sided and twosided samples with 300 g cement content and 20 mm anchoraged length are compared to each other for both ribbed and waved fibres. The maximal forces of one-sided samples were higher, which can be caused by the eccentric pull-out. However, the main features of the curves were similar in all examined cases. Contrary to [9] the results of the present experiments show that the two-sided pull-out phenomenon can be modelled by using one-sided pull-out samples with the reduction of the maximum force. Then the effect of the mortar strength (compressive strength) was examined. Increasing the amount of cement in the mortar resulted in higher mortar strength (Fig. 4). The increase was approximately linear for lower cement content. In case of higher cement content the increase in the strength was smaller. However, the relationship between the maximal slipping force and the cement content (or the mortar strength as well) cannot be modelled linearly (Fig. 4). Moreover, in case of high cement content adding more cement resulted in lower maximal slipping force. The dispersion of the samples was high. In this experiment mortar samples were made in laboratory circumstances. In case of not mortar but concrete matrix the dispersion of the results would be even higher. So, there is no general rule to describe the relationship between the maximal slipping force and the cement content, laboratory test is required in all cases. To examine the applicability of the existing theoretical models 150 one-side anchoraged samples were made with different mortar strength, fibre surface and anchoraged fibre length (Table 1). 92 A R C H I T E C T U R E C I V I L E N G I N E E R I N G E N V I R O N M E N T 2/2018 Figure 5. Maximal slipping force – Anchoraged length relationship Figure 4. Mortar strength/Maximal slipping force – Cement content relationship of two-sided pull-out tests, anchoraged length: 20 mm E X P E R IM EN TA L I N V E S T I G AT I O N S O F P U L L O U T B E H AV I O U R O F S Y N T H E T I C F I B R E S 3. THEORETICAL MODEL Few analytical models for the pull-out of synthetic fibres can be found in the literature [8 and 9]. A mor