An Experimental Setup To Measure The Conductivity Of A Solid Or Liquid Sample Utilizing Muti Frequency Lcr Meter

A computer-controlled automated data acquisition system is designed to measure the conductivity of the liquid (saline water) or the solid sample (rock saturated with saline water) in the frequency range 10 kHz to 2 MHz. The set-up is based on LCR (Inductor, Capacitor, and Resistor) multimeter and four-terminal sample holder system that was developed to reduce the contact resistance, to minimize any stray capacitance, and residual inductance associated with the test leads or the test fixture at high frequencies. However, the instrumentation calibration scheme cannot completely eliminate the aforementioned errors. In order to accomplish this, a calibration model is designed to compensate for the inherent error of the system. In this study, the conductivity of some samples was measured. The measured data was compared with conductivity provided by Society of Core Analysis Guideline (SCA-GL). The agreement between available data and experimental data is excellent. Introduction The increased ability of those in the petroleum industry to analyzed the formation characteristics from electrical resistivity data, it is imperative to have more precise method to measure that parameter 1,2 . Several types of resistivity sensors are available on MWD (Measurement-While-Drilling) tools. The earlier ones were short normal sensors operating near DC (Direct Current) 3, 4, 5 and coil-type sensor operating at 2 MHz 6, 7, 8 . For instance, the coil-type MWD resistivity tool measures phase and attenuation. Then, some conversion algorithms are used to transform the measured quantities in terms of apparent resistivities. In this conversion, the formation dielectric constant is assumed to be either a constant value or a known function of the resistivity which is not a correct assumption. Therefore, it is a common practice to obtain some samples from the core selected reservoir and then an actual electric permittivity are measured in the core measurement facility. P ge 10174.1 Proceedings of the 2005 American Society for Engineering Education Annual Conference & Exposition Copyright © 2005, American Society for Engineering Education In order to be able to utilize the measured dielectric permittivity instead of the assumed value, an automated computer controlled technique was developed for measuring the conductivity of the sample under the test at the frequency range of 10 kHz to 2 MHz. A multi-frequency LCR meter was used to measure the impedance of a four-terminal sample holder containing the core or the liquid sample. The system error of the LCR meter and sample holder is compensated by a set of compensation parameters obtained experimentally. After the system error is subtracted from the measured impedance, the conductivity of the sample is calculated. Instrumentation The schematic diagram of the low-frequency conductivity measurement is shown in Figure 1, it consists of an HP 4275A multi-frequency LCR meter, one sample holder, one desk-top computer, peripheral device, and four one-meter long coaxial cables with BNC (Bayonet Neill Concelman or Bayonet Nut Connector) connectors. The computer is used for controlling the system and data collection purposes. The communication is achieved via HP-IB cable that connects the computer to the multi-frequency LCR meter. The HP 4275A multi-frequency LCR meter is a fully automated test instrument designed to measure the parameters of an impedance element in the 10 kHz to 10 MHz range. The test signal level can be flexibly set at the desired amplitude within the range of 1mV to 1V. Figure 1. Block diagram of data acquisition system. Sample holder is comprised of two Plexiglas rectangular tanks which are connected together by a circular Plexiglas tube. Two pairs of platinum mesh serve both potential electrodes, and current electrodes. The potential electrodes are placed adjacent to the end surfaces of the rock sample. The current electrodes are placed parallel to the potential electrodes. Four pieces of the platinum wire connect the platinum electrodes to the BNC connector. P ge 10174.2 Proceedings of the 2005 American Society for Engineering Education Annual Conference & Exposition Copyright © 2005, American Society for Engineering Education Measurement Procedure The method of four-terminal measurement is used to reduce the contact resistance and to minimize any stray capacitance and residual inductance associated with the test leads or the test fixture at high frequencies (see Figure 2). Figure 2. Four-terminal measurement method. Page 10174.3 Proceedings of the 2005 American Society for Engineering Education Annual Conference & Exposition Copyright © 2005, American Society for Engineering Education Four, one-meter long, coaxial cables are used as leads from the BNC connector on the LCR meter to the sample holder. These coaxial cables are connected, at one end, to the high current, the high potential, the low potential, and the low current ports of the LCR meter. The other ends of these cables (the inner conductors) are connected to four terminals on the sample holder. The four outer conductors of these cables are short-circuited at the end near the sample holder, they serve as the return path for the measurement current. The same current flows through both the center conductors and the outer shield conductors (in opposition direction) so that no external magnetic fields are generated around the conductors. Thus, the test leads do not contribute any additional measurement error due to the self or the mutual inductance between the individual leads. Since the measurement circuit has inherent stray capacitances, residual inductances, and resistances, the measured values may be unacceptably influenced depending on the measurement range and the magnitude of the residual parameters. The ZERO offset adjustment function of the HP 4275A LCR meter automatically compensates for such residual, and minimizes the incremental error 9 . Setup Calibration To check on the accuracy of the system several two-terminal elements, such as brass and some precision resistors, were soldered to the potential electrodes one at the time and the current electrode was shorted to the potential electrode in each side using platinum wire. The impedance of these elements were measured, and some of these results are shown in Tables 1 and 2. The error appears to be very small at low resistance values. Table 1. A comparison between measured impedance and corrected impedance of the brass wire is shown. Frequency (kHz) 10 0.01 0.01 0.00 0.00 20 0.01 0.02 0.00 0.00 40 0.01 0.03 0.00 0.00 100 0.01 0.08 0.00 0.00 200 0.01 0.17 0.00 0.00 400 0.01 0.34 0.00 0.0