English (United Kingdom)

https://curated-unify.zendy.io/wp-json/zendy-region/v1/featured_content/oa?rat=en

https://curated-unify.zendy.io/wp-json/zendy-region/v1/highlighted_journal/

Global: Zendy Plus annual

Presents the access of premium content as premium feature

Premium Content

Presents the keyphrase highlighting as premium feature

Keyphrase Highlighting

Presents the summarisation as premium feature

Summarisation

Insights

Presents the pdf analysis as premium feature

PDF Analysis

Presents the zaia usage as premium feature

ZAIA

Global: Zendy Plus monthly

Global: Zendy Tools annual

Global: Zendy Tools monthly

Global: Zendy Free Plan

Among steel-making techniques Powder Metallurgy (PM) concept utilizes unique production cycle, consisting of powder compaction and sintering steps that give high productivity with low energy consumption and high material utilization. Due to the presence of residual porosity, mechanical properties of PM components are inferior in comparison with structural components produced by other technologies. Improvement of mechanical properties at the same level of porosity can be achieved primarily by adding variety of alloying elements. Therefore modern PM technology for production of high-performance PM parts for highly stressed steel components for automotive industry, for example, rely on techniques of utilization of different alloying elements additionally to adjustment of technological process depending on alloying system used. When talking about high-strength low-alloyed structural steels, the most common alloying elements, additionally to carbon, added in order to increase mechanical performance, are chromium, manganese, silicon and some other strong carbide and carbonitride-forming elements (V, Nb, Ti etc.). In comparison with classical steelmaking practice, alloying of PM steels is much more complicated as additionally to influence of alloying elements type and content on microstructure, mechanical properties, hardenability etc., number of additional aspects influencing powder production and further component processing has to be considered. Traditionally, PM high-strength steels are alloyed with Cu, Ni, and Mo. This results in a considerable difference in price of material between conventional and PM steels, used for the same high-load application, as the price of currently employed PM alloying elements like Mo and Ni is dozens of times higher in comparison with that of Cr or Mn. This situation creates a strong economical stimulation to introduce cheaper and more efficient alloying elements to improve the competitiveness of PM structural parts. So, why the potential of most common for conventional metallurgy alloying elements as Cr, Mn and Si is not utilized in PM? First and basic question that arise is how to introduce these elements in PM – as admixed elemental powder (or master-alloy) or by prealloying of the base steel powder. Chromium prealloyed steels are already successful introduced on the PM market. However due to peculiar properties of manganese (oxygen affinity, high vapour pressure, ferrite strengthening etc.) attempts to develop Mn sintered steels are still ongoing. Issue of appropriate alloying mode, that is the starting point of manganese introduction in PM, is the basic question that has to be answered at the beginning and is the basic topic of this chapter. The easiest way to introduce manganese is by admixing of ferromanganese powder that is cheap and widely available on the market in different grades. This approach was firstly proposes around 30 years ago and have been scrutinized thoroughly from different perspectives (Salak, 1980; Cias et al., 1999; Salak et al., 2001; Dudrova et al., 2004; Danninger et al., 2005; CiasW Schlieper & Thummler, 1979; Hoffmann & Dalal, 1979). First developed master-alloys containing manganese–chromium–molybdenum (MCM) and manganese–vanadium–molybdenum (MVM) had a wide range of mechanical properties depending on alloying content, sintered density and processing conditions. Nevertheless, these master-alloys faced with many problems during application (oxides formation during manufacturing process, high hardness of the particles that lead to intensive wear of compacting tools etc.) and fully disappears from manufacturing and research areas. Recent development of Fe–Cr–Mn–Mo–C master-alloys was much more successful and show promising properties for their future industrial utilization (Beiss, 2006; Sainz et al., 2006). High affinity of manganese for oxygen and Mn loss by sublimation can be minimized by lowering the manganese activity than can be done by Mn introduction in pre-alloyed state. However powder alloying by manganese faces some difficulties starting from powder production, handling and following compaction and sintering steps. This is connected with manganese selective oxidation on the powder surface during atomization and further annealing depending on processing conditions during powder production(Hryha et al., 2009-b; Hryha et al., 2010-a). A further negative impact of manganese utilization in pre-alloyed state is the expected lower compressibility of such pre-alloyed powders due to ferrite solid solution strengthening by manganese. This chapter is focused on the influence of alloying mode, utilizing premix systems with different ferromanganese grades and high-purity electrolytic manganese as well as fully prealloying of water atomized powder. While respecting all the benefits and problems with sintered steels alloyed with manganese some basic directions have been chosen — theoretical evaluations of required sintering atmosphere composition for preventing of manganese alloyed steels from oxidation during every stage of sintering, analyzes of sintering cycle coupling with simultaneous atmosphere monitoring and further analysis of sintered specimens using number of advanced spectroscopy and thermoanalytic techniques. Various phenomena, connected with manganese evaporation and reduction/oxidation behaviour of manganese alloyed sintered steels were theoretically evaluated and tested experimentally applying interrupted sintering experiments, when specimens where sampled at different stages of the sintering cycle for extensive study by HR SEM+EDX, XPS, TG+MS etc. Thermodynamic calculations enabled to determine a required sintering atmosphere composition (maximal permitted partial pressures of active gases CO/CO2/H2O) for preventing of Mn alloyed steels prepared by different alloying mode from oxidation during every stage of sintering. The results were verified by continual monitoring of CO/CO2/H2O profiles in sintering atmosphere and further analysis of sintered specimens.

intech ebooks

The Sintering Behaviour of Fe-Mn-C Powder System, Correlation between Thermodynamics and Sintering Process, Manganese Distribution and Microstructure Composition, Effect of Alloying Mode