English (United Kingdom)

https://curated-unify.zendy.io/wp-json/zendy-region/v1/featured_content/oa?rat=en

https://curated-unify.zendy.io/wp-json/zendy-region/v1/highlighted_journal/

Global: Zendy Plus annual

Presents the access of premium content as premium feature

Premium Content

Presents the keyphrase highlighting as premium feature

Keyphrase Highlighting

Presents the summarisation as premium feature

Summarisation

Insights

Presents the pdf analysis as premium feature

PDF Analysis

Presents the zaia usage as premium feature

ZAIA

Global: Zendy Tools annual

Global: Zendy Free Plan

Global: Zendy Tools monthly

Global: Zendy Plus monthly

1Cr18Mn8Ni5N austenitic stainless steel is welded by the gas metal arc welding process to study the effect of three kinds of current on the microstructure and properties of welded joints. The experiment finds that the microstructure of weld metal is austenite and the morphology of austenite are thin strips, massive and coarse columnar in 162A, 170A, 178A, respectively. The microstructures of HAZ are austenite and pro-eutectoid ferrite. The joint comprehensive mechanical properties are the best when the current is 170A. The fracture mode of weld joints is fracture toughness. Introduction In order to reduce production costs, adding small Mn and nickel instead of nitrogen to produce a nickel-based stainless steel. The 1Cr18Mn8Ni5N steel belong Cr-Mn-Ni-N type section of nickel austenitic stainless steel. This steel has good shaping and weldability compared with traditional Cr-Ni austenitic stainless steel. This steel is widely used in aviation, aerospace, power plants, nuclear reactors and other engineering structures with serving in high temperature, high pressure and harsh conditions. The welded joints are usually more vulnerable parts in the metal components, so the mechanical properties of welded joints become major problems[1-5]. Currently, the welding method of 1Cr18Mn8Ni5N steel is mainly used TIG welding. The TIG welding process is a popular process in this area where a high degree of quality and accuracy is required. Moreover, TIG welding is more preferable than SMAW and MIG process because of the lower heat input[1]. The effect of welding current on the weld microstructure and mechanical properties of welded joints were studied, which was help to provide the basic application information for 1Cr18Mn8Ni5N stainless steel sheet welding. Material and Methods The material was 1Cr18Mn8Ni5N steel with solution treatment at 1100°C, and the sheet size was 200mm×100mm×2.5mm, butt welding plate was used in this experiment. The welding wire was H0Cr19Ni11Mo3 and the welding wire diameter was 1.6mm. The main compositions of base metal and welding wires were showed in Table 1. The equipment was orthogonal frequency arc DC TIG welding machine with pure argon gas protection and automatic filler wire.The welding parameters were showed in Table 2 Prior to welding, the specimens were thoroughly washed with acetone to clean greasy dirt and impurities. To study mechanical properties, the welded joint was sliced by abrasive cutter, and then machined into the required dimensions to get tensile specimens. In order to examine the microstructures of the welded joint, samples were prepared by cutting off weldment in the transverse direction. Samples were grinded by using silicon carbide waterproof electro coated abrasive papers. The tensile test International Conference on Material Science and Application (ICMSA 2015) © 2015. The authors Published by Atlantis Press 592 was carried on the W9W-50 electronic universal testing machine, the samples were stretched under 2mm/min. The samples were etched by corrosive (HNO3:HCL:H2O=1:1:1). The microstructure was observed with 4XB-TV models inverted microscope. 401MVD digital micro-hardness tester was used to analysis micro-hardness distribution of the welded joints. The SEM was used to observe the fracture morphology of welded joints Tab.1 Main chemical compositions of base metal and welding wires C Si Mn Cr Ni N Mo 1Cr18Mn8Ni5N 0.15 1.0 7.5-10.0 17.0-19.0 4.0-6.0 ≦0.25 — H0Cr19Ni11Mo3 ≦0.06 0.3-0.7 1.0-2.0 18.0-20.0 10.0-12.0 — 2.0-3.0 Tab. 2 Welding process parameters No. Current/A Welding speed mm/min Wiring speed mm/min Gas flowing rate L/min 1 162 260 820 15 2 170 260 820 15 3 178 260 820 15 Results and Analysis Microstructures and Analysis The microstructure of weld metal was single austenite, the HAZ (heat-affected zone) were consisted of pro-eutectoid ferrite and austenite which were showed in figure 1-3.When the welding current was 162A, the microstructure of weld metal was small massive, elongated austenite and uneven distribution. When the current was 170A, the microstructure of weld metal was blocky austenite and uniform distribution. When the current was 178A, the microstructure of weld metal was coarse columnar austenite, and the austenite had strong directionality distribution. Due to the austenitic stainless steel had small thermal conductivity, large thermal expansion coefficient, therefore it was difficult for the weld pool metal to radiate heat during welding[2-4]. When the current was 162A, 170A, 178A, respectively, the heating temperature of pool was gradually increased, thus the superheat of pool metal was successively larger and larger, resulting in weld metal got longer and longer residence time at high temperature. Therefore the austenite grain growth tendency was increased, so the austenite morphology in the weld were separately small block, strip, massive and columnar. Especially when the current was 178A, the superheat of the pool metal was maximum, the weld metal had the longest time to stay in high temperature and the grains had the largest growth tendency, thus the morphology of austenite was columnar in weld. The figures 1 to 3 showed the weld didn’t exit the ferrite phase, but the HAZ had pro-eutectoid ferrite. The different regions microstructure in HAZ had been showed in figure 4 .The morphology of pro-eutectoid ferrite was thin strips and distributed along the austenite grain boundaries. The content of ferrite in fusion zone was little. But the amount of ferrite increased significantly in fully recrystallization zone and the size of grain was fine. The amount of ferrite in incompletely recrystallization zone was least. The precipitation and morphology of pro-eutectoid ferrite were pertinent to the composition of weld metal and cooling rate[6].When the current were 162A,170A and 178A, the pool metal had long time to stay in high temperature and the cooling rate of pool was slow, the content of austenite stabilizing elements was in high level, thus the weld microstructure was single austenite phase. Due to the temperature of HAZ was lower than weld and the cooling speed was faster, when the HAZ was cooled from high-temperature to higher temperature (770-680°C),the pro-eutectoid ferrite precipitated along austenite grain boundaries[6]. The welding thermal cycles lead to peak temperature was different in different zones of HAZ, resulted in the grain sizes of austenite was 593 different and also lead to the precipitation and growth of pro-eutectoid ferrite were not at the same time in different regions of HAZ. Therefore the austenite grain sizes and pro-eutectoid ferrite content were different in HAZ. Fig.1 Joint microstructures of No.1: a-Weld.b-HAZ Fig.2 Joint microstructures of No.2: a-Weld.b-HAZ Fig.3 Joint microstructures of No.3: a-W.b-HAZ a-fusion zone.b-completed recrystallization zone.c-incompleted recrystallization zone Fig.4 HAZ Microstructures of No. 3 Tensile test of Welded Joints Data in table 3 showed that the tensile strength of welded joints in three kinds of current. When the welding current were 162A,170A and 178A, respectively, the tensile strength of welded joints were 663.96MPa, 692.84Mpa and 610.34MPa.When the current was 170A, the joint reduction of area were also higher. According to the Hall-Petch formula, that the more the size of grains was finer and more uniform, the more the grain strength was higher and ductility was also better[7].When the current were 162A or 178A,the austenite morphology in weld were small block, strip or coarse columnar, and

Effect of TIG Weld Current on 1Cr18Mn8Ni5N Austenitic Stainless Steel Welding Microstructure and Mechanical Properties