English (United Kingdom)

https://curated-unify.zendy.io/wp-json/zendy-region/v1/featured_content/oa?rat=en

https://curated-unify.zendy.io/wp-json/zendy-region/v1/highlighted_journal/

Global: Zendy Plus annual

Presents the access of premium content as premium feature

Premium Content

Presents the keyphrase highlighting as premium feature

Keyphrase Highlighting

Presents the summarisation as premium feature

Summarisation

Insights

Presents the pdf analysis as premium feature

PDF Analysis

Presents the zaia usage as premium feature

ZAIA

Global: Zendy Tools annual

Global: Zendy Free Plan

Global: Zendy Tools monthly

Global: Zendy Plus monthly

Heat alleviation from surfaces exposed to high heat has been of prominence with the advent of new technologies in the electronic industry. The usage of regular materials and alloys has been used to the hilt and the manufacture of new alloys being slow and with the advent of Metal Matrix Composites, their usage as heat dissipation materials has taken a front row. This is the initiation into developing an MMC of Al6061 with silver coated copper particles to be researched. The usage of Al6061 as a heat sink material and the addition of copper to it to enhance the heat dissipation capability of the material are found to yield encouraging results. This composite when further heat treated yielded even good results that surpassed the usual Al6061 capability of heat augmentation by 39%. Taguchi analysis and ANOVA are performed for the given data. Keyword: Stir Casting, Al 6061, MMC’s, Taguchi Analysis, ANOVA, Heat Dissipation INTRODUCTION The usage of extended surfaces for enhanced heat transfer is the most used methodology for heat relieval from a hot surface. The characterization and analysis on various shapes of fins have been performed during the recent history to promulgate a good fin material and also the right shape of the fin that can dispense higher heat generated at a smaller place as in electronics. An array of such fins designed and put in a small area for increase in the surface area are being researched as the heat being generated by electronics is on the increase with the innovation and enhancement in the technology. The design of an array of fins had to be optimized since the number of fins if higher may affect the heat transfer adversely. The negative impact may be due to the resistance offered to the flow of air and the boundary layer interferences [1]. The investigations on rectangular fin array are reported extensively in the literature [2-8]. Apart from rectangular fins there are limited studies performed on other fin configurations [9]. Thermal performance and mass minimization of extended surfaces was studied for rectangular, pin and triangular shaped arrays for effective heat dissipation from various surfaces by different convection models natural and forced[10,11]. With the availability of various advanced materials and methodologies of transport of thermal media deposition the landscape of heat dissipation has changed for good [12,13].The size of sink, the number of fins, the gaps between the fins, the area of sink exposed to atmosphere have an close relation on enhancing the convection effect and increasing the heat sink ability [14,15]. Taguchi [16] method for design of experiments (DOE) and the analysis of variance (ANOVA) that is most widely used in the production process are employed for choosing optimized design parameters. Optimization of heat sinks is carried out using different techniques for different configurations [18-20]. From the literature it is observed that pin fin coated with carbon nano tubes has made a remarkable enhancement in heat transfer, but very less work is reported on composites being used for manufacturing heat sinks. In the present study regular heat sink material Al 6061 is mixed with silver treated copper particles for preparation of MMC. Silver treated copper particles are selected due to their high thermal conductivity and better wettability. The produced MMC’s heat dissipation rate is compared in as-cast and post heat treated conditions for different heat inputs and velocities of air. Further numerical investigation is carried out using Taguchi and ANOVA, in the subsequent sections. The process of manufacture of the MMC is elaborated in the next section. Journal of Thermal Engineering, Research Article, Vol. 4, No. 2, Special Issue 7, pp.1813-1820, February, 2018 1814 EXPERIMENTATION The composite of Al 6061 alloy with the silver coated copper (10% Silver is coated on 90% copper of diameter 30-50microns) is prepared using a stir casting machine as shown in Figure 1. Base material (matrix) chosen is Al 6061 which is the regular heat sink material being used in majority of electronic equipment for heat dissipation. A graphite crucible having a 3 phase bottom pour electric resistance furnace with a cover is used to melt the Al 6061 alloy which is cut into reasonable sizes for introduction into the furnace, and the melting temperature is maintained at 750C. A mechanical stirrer(made of mild steel) having three blades being run by a 0.5 HP motor is used to stir the composition into which the silver coated copper powder is introduced after proper heating in a hot air oven to remove any incidence of water vapour. This so heated silver coated copper power is added and the composition is stirred for 5 mins before pouring to ensure proper mixing of the matrix and the reinforcement and to remove any gas entrapments. The properly stirred molten liquid is poured into cast iron moulds of 150x100 mm to obtain castings. The reinforcement percentages are chosen as 5, 10 and 15 percent by weight. The as-cast rods are machined and a cylindrical fin is manufactured with the required thread cut at one end so as to enable it to be loaded onto the pin fin apparatus that is used for experimentation. Heat treatment is performed on one set of rods thus manufactured of varying compositions. The rods are furnace heated to a temperature of 540C and are allowed to soak for a period of 1 hour and are then quenched in a water bath. The as-cast and heat treated bars are loaded on the pin fin apparatus (Figure 2) and experimented upon, the results and analysis of which are shown in the subsequent sections. From the uncertainty analysis [21], it is found that temperature uncertainty is ±0.5%. Experimental validation is carried for pure aluminium as test fin, the result obtained from experiment is compared with correlations of pin fin [22]. It is observed that deviation was around 6% with correlations. Figure 1. Stir Casting Machine Figure 2. Pin-Fin apparatus Journal of Thermal Engineering, Research Article, Vol. 4, No. 2, Special Issue 7, pp.1813-1820, February, 2018 1815 Taguchi Technique The process/input parameters that influence the output characteristic of temperature are identified and the heat transferred is experimented and tabulated in this section. The identified process parameters are heat input in watts, distance from the heat input on the fin in mm and composition of the MMC in percentages of silver coated copper particles, their levels are shown in Table 1. Length of the fin and diameter considered for the experiment are 15.2 and 1.1 cm. The design of experiments along with optimization of the process parameters is performed using Taguchi method. The three process parameters with three levels yield nine experiments using the L9 orthogonal array. The array is shown in Table 2.The temperatures along the fin surface are recorded using an infrared pyrometer (fluke 59 max) that can measure temperatures in the range of -50C to 500C. Table 1. Input parameters with chosen their levels Input parameter Level 1 Level 2 Level 3 Heat input(Watts) 35 50 65 Distance from source(mm) 27 54 81 Composition (wt %) 5 10 15 Table 2. L9 orthogonal array Experiment Number Heat input (W) Distance from source (mm) Composition (Wt %) 1 1 1 1 2 1 2 2 3 1 3 3 4 2 1 2 5 2 2 3 6 2 3 1 7 3 1 3 8 3 2 1 9 3 3 2 The data is accumulated and populated into Tables 3 and 4;these tables illustrate the data for various inputs on the materials prior to heat treatment and after heat treatment. S/N ratio’s for the data recorded are also shown in the tables for clear understanding of the outputs gathered. The smaller S/N ratio is computed based on the quality of the characteristics. The objective of the experimentation is to enhance the heat transfer rate; the objective of enhancement of heat transfer is illuminated by the reduction in the surface temperature on the fin. S/N ratios for the data accumulated in the tables are analysed using equation 1 wherein the smaller the value of the ratio the better is the result [18]. S N = −10log10(∑ y 2 /n) (1) Table 3. Data accumulated for temperatures on the pin fins prior to heat treatment Exp. No. Heat input (W) Distance from source (mm) Composition (Wt %) Temperature (C) 1 1 1 1 54.2 2 1 2 2 44.2 3 1 3 3 38.1 4 2 1 2 69.5 5 2 2 3 54.7 6 2 3 1 42.3 7 3 1 3 84.3 8 3 2 1 61.1 9 3 3 2 50.2 Journal of Thermal Engineering, Research Article, Vol. 4, No. 2, Special Issue 7, pp.1813-1820, February, 2018 1816 Table 4. Data accumulated for temperatures on the pin fins after to heat treatment Exp. No. Heat input (W) Distance from source (mm) Composition (Wt %) Temperature (C) 1 1 1 1 57.0 2 1 2 2 48.1 3 1 3 3 41.1 4 2 1 2 72.8 5 2 2 3 60.4 6 2 3 1 45.1 7 3 1 3 88.7 8 3 2 1 62.8 9 3 3 2 53.9 The data accumulated is further used to do an efficiency analysis to find the efficiency of the fin with the best composition that can be used; this is elaborated in the next section. Fin Analysis Analysis that is performed on the as-cast and heat treated samples of varying compositions are accomplished using the efficiency formulations [18,22] for analysing the performance of the fins manufactured. Efficiency of the fin is calculated from the following equation; η = Qfin Qmax = Qfin hAsurf(Tb−Ta) (2) Where Qfin is calculated for short fin with convection at tip from the temperature profile along the fin by considering temperature at 15 different points T−Ta Tb−Ta = c1e −mx + c2e mx (3) Where

EXPERIMENTAL INVESTIGATION ON AL6061 SILVER COATED COPPER METAL MATRIX COMPOSITE CIRCULAR EXTENDED SURFACES PRE AND POST HEAT TREATMENT