English (United Kingdom)

https://curated-unify.zendy.io/wp-json/zendy-region/v1/featured_content/oa?rat=en

https://curated-unify.zendy.io/wp-json/zendy-region/v1/highlighted_journal/

Global: Zendy Plus annual

Presents the access of premium content as premium feature

Premium Content

Presents the keyphrase highlighting as premium feature

Keyphrase Highlighting

Presents the summarisation as premium feature

Summarisation

Insights

Presents the pdf analysis as premium feature

PDF Analysis

Presents the zaia usage as premium feature

ZAIA

Global: Zendy Tools annual

Global: Zendy Free Plan

Global: Zendy Tools monthly

Global: Zendy Plus monthly

ABSTRAK PENGARUH PEMANASAN KERNEL UO 2 DALAM MEDIUM GAS ARGON TERHADAP SIFAT FISIS KERNEL UO 2 SINTER . Pengaruh pemanasan kernel UO 2 dalam medium gas argon terhadap sifat fisis kernel UO 2 sinter telah dipelajari. Pemanasan dilakukan dalam reaktor sinter tipe bed. Penelitian ini bertujuan untuk memperoleh sifat fisis kernel UO 2 sinter sesuai dengan persyaratan penggunaan sebagai bahan bakar nuklir. Sampel yang digunakan adalah kernel UO 2 hasil reduksi pada 800 o C selama 3 jam yang mempunyai densitas sebesar 8,13 g/cm 3 ; porositas sebesar 0,26; rasio O/U sebesar 2,05; diameter sebesar 1146 µm dan kebulatan sebesar 1,05. Sampel dimasukkan ke dalam reaktor sinter, lalu divakumkan untuk mengusir udara dan pengotor dalam reaktor. Setelah itu dialirkan air pendingin dan gas argon pada tekanan 5 mPa dengan kecepatan 1,5 liter/menit secara kontinyu. Temperatur reaktor dinaikkan dengan variasi pada 1200 – 1500 o C dan waktu divariasi selama 1 – 4 jam. Kernel UO 2 sinter yang dihasilkan, dianalisis sifat fisisnya meliputi densitas, porositas, diameter, kebulatan dan luas muka spesifik. Densitas dianalisis menggunakan piknometer dengan larutan CCl 4 , porositas ditentukan menggunakan persamaan Haynes. Diameter dan kebulatan diamati menggunakan mikroskop Dino-lite. Luas muka spesifik ditentukan menggunakan surface area meter Nova-1000. Hasil yang diperoleh menunjukkan bahwa pemanasan kernel UO 2 dalam medium gas argon perpengaruh terhadap sifat fisis kernel UO 2 sinter. Sifat fisis kernel UO 2 relatif baik diperoleh pada temperatur pemanasan 1400  o C selama 2 jam dan dihasilkan kernel UO 2 sinter dengan densitas sebesar 10,14 g/mL, porositas sebesar 7 %, diameter sebesar 893 µm, kebulatan sebesar 1,07 µm, luas muka spesifik sebesar 4,68 m 2 /g dan penyusutan padatan sebesar 22,08 %. Besaran sifat fisis ini hampir sama dengan sifat fisis kernel UO 2 yang digunakan sebagai bahan bakar nuklir . Kata kunci : Kernel UO 2 , pemanasan, sifat fisis, densitas, porositas, luas muka spesifik dan kebulatan. ABSTRACT THE HEATING OF UO 2 KERNELS IN ARGON GAS MEDIUM ON THE PHYSICAL PROPERTIES OF SINTERED UO 2 KERNELS. The heating of UO 2 kernels in argon gas medium on the physical properties of sinter UO 2 kernel s was conducted . The heated of the UO 2 kernels was conducted in a sinter reactor of a bed type. The sample used was the UO 2 kernels resulted from the reduction results at 800 o C temperature for 3 hours that had the density of 8.13 g/cm 3 ; porocity of 0. 26; O/U ratio of 2.05 ; diameter of 1146 µm and sphericity of 1 . 05. The sample was pu t into a sinter reactor, then it was vacumed by flowing the argon gas at 180 mmHg pressure to drain the air from the reactor. After that , the cooling water and argon gas were continuously flowed with the pressure of 5 mPa with 1.5 liter/minutes velocity. The reactor temperature was increased and variated at 1200-1500 o C temperature and for 1-4 hours. The sinters UO 2 kernel s resulted from the study were analyzed in term of their physical properties including the density, porosity, diameter, sphericity , and specific surface area. The d ensit y was analyzed using pycnometer with CCl 4 solution . The p orosit y was determined using Haynes equation . The d iameter s and sphericit y were showed using the Dino-lite microscope. The s pecific surface area was determined using s urface a rea m eter Nova-1000. The obtained products showed tha the heating of UO 2 kernel in argon gas medium were influenced on the physical properties of sinters UO 2 kerne l . The condition of best relatively at 1400 o C temperature and 2 hours time. The product resulted from the study was relatively at its best when heating was conducted at 1400 o C temperature and 2 hours time, produced sinters UO 2 kernel with densit y of 10 . 14 gr/ ml ; porosity of 7 % ; diameters of 893 µm; sphericit y of 1 . 07 and specific surface area of 4 . 68 m 2 /g with solidify shrinkage of 22 % . Keywords : UO 2 kernel , heating, physical properties, density, porosity, specific surface area and sphericity.

PENGARUH PEMANASAN KERNEL UO2 DALAM MEDIUM GAS ARGON TERHADAP SIFAT FISIS KERNEL UO2 SINTER