English (United Kingdom)

https://curated-unify.zendy.io/wp-json/zendy-region/v1/featured_content/oa?rat=en

https://curated-unify.zendy.io/wp-json/zendy-region/v1/highlighted_journal/

Global: Zendy Plus annual

Presents the access of premium content as premium feature

Premium Content

Presents the keyphrase highlighting as premium feature

Keyphrase Highlighting

Presents the summarisation as premium feature

Summarisation

Insights

Presents the pdf analysis as premium feature

PDF Analysis

Presents the zaia usage as premium feature

ZAIA

Global: Zendy Tools annual

Global: Zendy Free Plan

Global: Zendy Tools monthly

Global: Zendy Plus monthly

Pipelines produced from High Strength Low Alloy steels (HSLA) are a safe and cheap way to transport large quantities of petroleum and gas. HSLA steels offers mechanical and economic advantages. When HSLA steels are exposed to environments containing hydrogen sulphide (H2S), the steel can corrode and generate atomic hydrogen in the surface wich can diffuse and trapped, leading loss of mechanical properties and subsequent failures. The infrastructure to transport oil and gas represent a high cost investment, in adittion, they must be free from degradation processes that can causes severe health and environmental impacts. For this reason, the development of materials with high performance in aggressive environments is required. The aim of this study is to analyze and compare the corrosion behavior, hydrogen permeability and its relation with the susceptibility to Hydrogen Induced Cracking (HIC) of HSLA steels in environments containing H2S, with emphasis on the influence of microstructure. Normalizing and quenching heat treatments were applied in two different API 5L X65 pipelines for sour service. Three conditions were obtained (as received, normalized and quenched). The as received has a microstructure of ferrite / pearlite and ferrite / acicular ferrite, respectively; the microstructure of normalized specimens consist of ferrite / pearlite and finally quenched steels presented a microstructure of martensite. Solution A (acetic acid containing sodium chloride), according to NACE TM0284-2011 standard and saturated with H2S was used. The materials were tested by linear polarization technique, hydrogen permeability and Hydrogen Induced Cracking test (HIC). HIC tests were performed according to NACE TM0284-2011 standard. Optical microscope and scanning electron microscope were used for microstructural, corrosion and cracking characterization. Rp values show a slight difference between the different samples studied (120 .cm e 210 .cm); the martensite microstructure (quenched) showed the lower corrosion resistance. Mansfeld (1973) method was used to calculate the corrosion rates from polarization curves. The Tafel slopes are differents between samples making evident the formation of corrosion products. Despite the growth of those corrosion products, the corrosion rate was not affected, since these products are dissolved in the solution A, providing a low corrosion protection. A modified Devanathan-Stachurski cell was used for the hydrogen permeability tests. It was used the solution A, with injection of H2S in the charging cell, and 0.1M NaOH solution on the oxidation cell. The hydrogen effective diffusivity, sub-surface concentration of atomic hydrogen at the charging side and number of hydrogen-trap sites were calculate by tlag method. Moreover, the experimental data were fitted using an equation derived from Fick’s second law, in order to determinate the diffusion coefficient. The diffusion coefficient obtained from both methods were compare showing similar results. The quenching samples showed the lower diffusion coefficient, higher hydrogen concentration and number of trap sites. The steels in the as received and normalized conditins did not show cracks in Hydrogen Induced Cracking test; in the other hand, quenched samples presents cracks. The results shoed the relationship between the amount of interface and the corrosion rate. Being the martensitic microstructure the one with the higher corrosion rate. The diffusion coefficient in the martensitic microstructure, is a result of the high amount of interfaces and high dislocation density, leading to a lower diffusion coefficient, higher hydrogen concentration and number of trap sites. In the Hydrogen induced Cracking test the martensitic microstructure has shown the lower resistance to crack. The nucleation and propagation of the cracks in martensite depend of mechanisms that may act simultaneously: (i) nucleation of micro-cracks in preferential sites, (ii) formation of H2 in micro-cavities, with increase the local pressure, and (iii) hydrogen migration to the tip of the crack, decreasing the cohesive force in the lattice. However, the relationship between microstructure and Hydrogen Induced Cracking can not be generalized, since the susceptibility to cracking depends of several factors, like number of trap sites, binding trap energy, microstructural distribution and trap sizes. In addition, the presence of regions of low ductility can result in easy cracks nucleation and propagation. This thesis contributed to the understanding of the mechanisms that lead to hydrogen embrittlement and hydrogen damage, showing the relationship between microstructure, corrosion rate, diffusion and cracking, I ncreasing the scientific knowledge about the standard tests actually used to evaluate the performance of microalloyed steels in sour environments.

Corrosão, permeabilidade e danos provocados por hidrogênio em aços microligados.